SewGraph

janome · verified physical machine

MC9500

View cited identity evidence · 3 unique proof passages

Jump to: Proof E1, Proof E2, Proof E3

verified exact machine · core systems pending

Identity verified · evidence for each answer

Using and maintaining this machine

Check the conditions alongside each answer. Foot attachment, shank type and adapter requirements are separate; one does not establish universal accessory fit.

Bobbins and hook

Insertion direction

conditional

Place the bobbin so the thread runs off counterclockwise.

Source evidence · 1 unique proof passage: Profile Proof E1

Threading path

conditional

Guide the thread into the front notch, draw it left between the tension-spring blades and into the side notch, pull about 10 cm (4 inches) to the rear, then reattach the hook cover plate.

Source evidence · 1 unique proof passage: Profile Proof E1

Needles and threading

Insertion orientation

conditional

Insert the needle with its flat side to the rear.

Source evidence · 1 unique proof passage: Profile Proof E2

Insertion depth

conditional

Push the needle against the stopper pin and tighten the needle-clamp screw firmly.

  • Turn off and disconnect power before changing the needle.

Source evidence · 1 unique proof passage: Profile Proof E2

Straightness check

conditional

Place the flat side on a flat surface; the gap should remain consistent, and never use a blunt needle.

Source evidence · 1 unique proof passage: Profile Proof E3

Presser feet and adapters

Removal

conditional

Raise the needle fully and raise the presser-foot lifter, then press the red button on the back of the holder so the foot drops off.

Source evidence · 1 unique proof passage: Profile Proof E4

Attachment

conditional

Place the foot pin under the holder groove and lower the presser bar to lock the foot in place.

Source evidence · 1 unique proof passage: Profile Proof E4

Extra lift

conditional

The lifter can raise the foot about 6 mm (1/4 inch) above its normal up position when extra pressure is applied.

Source evidence · 1 unique proof passage: Profile Proof E5

Sources for the owner answers above
Official OEM PDF

What this passage supports

  • Extra lift: The lifter can raise the foot about 6 mm (1/4 inch) above its normal up position when extra pressure is applied.
You can raise the Presser Foot about 6 mm (1/4 inch) higher than the normal up position by exerting more pressure when lifting the Presser Foot Lifter.
Document
Janome Memory Craft 9500 Instruction Book
Issuer
Janome
Extraction
Visually verified transcription of a scanned page
Visual verification
Checked 2026-09-14T23:20:00Z. The page image and transcription are hash-bound in the evidence record.
PDF page
10
Open source
Open OEM landing/support page (cited PDF unavailable)
Advanced technical receipt
Asset SHA-256
0c481a54e942721f80268d068552232497829faa777198f8c2df7218144d583b
Locator
277034cf2f16c42749abfd45a0f1a403e43d235396fbd9a10552211b8d78d76e
Destination status
landing_page_fallback
Official OEM PDF

What this passage supports

  • Insertion orientation: Insert the needle with its flat side to the rear.
  • Insertion depth: Push the needle against the stopper pin and tighten the needle-clamp screw firmly.
Raise the needle by pressing the Up/Down Needle button and lower the presser foot. Turn off the power switch. Insert a new Needle into the Needle Clamp with the Flat Side of the needle to the rear. Push it up against the stopper pin and tighten the Needle Clamp Screw firmly. Always make sure to turn the power switch off and disconnect the machine from power supply before changing the needle.
Document
Janome Memory Craft 9500 Instruction Book
Issuer
Janome
Extraction
Visually verified transcription of a scanned page
Visual verification
Checked 2026-09-14T23:20:00Z. The page image and transcription are hash-bound in the evidence record.
PDF page
19
Open source
Open OEM landing/support page (cited PDF unavailable)
Advanced technical receipt
Asset SHA-256
0c481a54e942721f80268d068552232497829faa777198f8c2df7218144d583b
Locator
5b69a9623c2d98bc209c0dc80840dc6e7752207123b7c67152dfb4c988d69c35
Destination status
landing_page_fallback
Official OEM PDF

What this passage supports

  • Insertion direction: Place the bobbin so the thread runs off counterclockwise.
  • Threading path: Guide the thread into the front notch, draw it left between the tension-spring blades and into the side notch, pull about 10 cm (4 inches) to the rear, then reattach the hook cover plate.
Place the Bobbin in the Bobbin Holder with the Thread running off counterclockwise. Guide the thread into the Front Notch (A) on the front of the Bobbin Holder. Draw the thread to the left, sliding it between the tension spring blades. Continue to draw the thread lightly until the thread slips into the Side Notch (B). Pull out about 10 cm (4 inches) of thread to the rear. Reattach the Hook Cover Plate.
Document
Janome Memory Craft 9500 Instruction Book
Issuer
Janome
Extraction
Visually verified transcription of a scanned page
Visual verification
Checked 2026-09-14T23:20:00Z. The page image and transcription are hash-bound in the evidence record.
PDF page
15
Open source
Open OEM landing/support page (cited PDF unavailable)
Advanced technical receipt
Asset SHA-256
0c481a54e942721f80268d068552232497829faa777198f8c2df7218144d583b
Locator
69af8e81800acbaf47aeb8a5fcbbd2c766031fd96ce79274c69f738b0bcbb48e
Destination status
landing_page_fallback
Official OEM PDF

What this passage supports

  • Removal: Raise the needle fully and raise the presser-foot lifter, then press the red button on the back of the holder so the foot drops off.
  • Attachment: Place the foot pin under the holder groove and lower the presser bar to lock the foot in place.
Removing the presser foot: Press the Up/Down Needle Button to raise the needle to its highest position and raise the Presser Foot Lifter. Press the Red Button on the back of the foot holder. The Presser Foot will drop off. Attaching the presser foot: Place the selected Presser Foot so that the pin on the foot lies just under the Groove of the Foot Holder. Lower the Presser Bar to lock the foot in place.
Document
Janome Memory Craft 9500 Instruction Book
Issuer
Janome
Extraction
Visually verified transcription of a scanned page
Visual verification
Checked 2026-09-14T23:20:00Z. The page image and transcription are hash-bound in the evidence record.
PDF page
10
Open source
Open OEM landing/support page (cited PDF unavailable)
Advanced technical receipt
Asset SHA-256
0c481a54e942721f80268d068552232497829faa777198f8c2df7218144d583b
Locator
709651ef2d90d82e446c3894a6045b5aed41439aa81ada353ad0a0078c77c5a5
Destination status
landing_page_fallback
Official OEM PDF

What this passage supports

  • Straightness check: Place the flat side on a flat surface; the gap should remain consistent, and never use a blunt needle.
To check needle straightness, place the flat side of the needle onto something flat. The gap between the needle and the flat surface should be consistent. Never use a blunt needle.
Document
Janome Memory Craft 9500 Instruction Book
Issuer
Janome
Extraction
Visually verified transcription of a scanned page
Visual verification
Checked 2026-09-14T23:20:00Z. The page image and transcription are hash-bound in the evidence record.
PDF page
19
Open source
Open OEM landing/support page (cited PDF unavailable)
Advanced technical receipt
Asset SHA-256
0c481a54e942721f80268d068552232497829faa777198f8c2df7218144d583b
Locator
a6c51de76681c9ec75e871f1f56bcf0b431a67c09a562e1e5ec13d7923389650
Destination status
landing_page_fallback
Machine facets and OEM groups

Cited machine facets

Identity and compatibility badges

Identity families, physical traits, and OEM accessory groups stay separate. A group badge applies only to its named program and domains.

OEM group · accessory, presser footJanome Accessory Compatibility Category: Janome Category A
Detailed specifications, compatible parts, and source library

Evidence coverage

Core answers and cited items

Machine category: Not yet established

Core domains answered: None yet

Domains with cited compatible items: presser foot (26)

Unknown is not incompatible. A missing answer means the current official evidence does not support one yet.

Specifications

Documented machine facts

Multiple cited representations for one field share one row. SewGraph preserves every value and exact proof passage; it does not guess which representation is “raw” or “normalized” when the public projection does not label that distinction.

presser foot

presser foot shank heightHigh

View exact evidence · 1 unique proof passage: Proof E4

Parts & accessories

31 documented relationships

A two-hop result joins the machine’s official accessory-group membership to the OEM part matrix. Open the evidence to inspect both hops.

31 relationships shown

presser foot · 26

FRINGING FOOT
200-016-108
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E6

View proof JSONReport this claim
TAPING FOOT
767-412-018
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E7

View proof JSONReport this claim
TAPING FOOT WITH REEL
202-033-004
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E8

View proof JSONReport this claim
BOBBIN HOLDER FOR FREE QUILTING AND HAND-LOOK STITCHING
200-445-007
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E9

View proof JSONReport this claim
CONCEAL ‰ ZIPPER FOOT
767-410-016
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E10

View proof JSONReport this claim
BLIND STITCH FOOT
202-040-004
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E12

View proof JSONReport this claim
EVEN FEED FOOT
767-403-016
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E13

View proof JSONReport this claim
1/4 INCH SEAM FOOT
767-820-105
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E14

View proof JSONReport this claim
BINDER FOOT WITH GUIDE
796-402-004
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E16

View proof JSONReport this claim
FREE MOTION COUCHING FOOT SET
202-110-006
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E17

View proof JSONReport this claim
FREE MOTION FRAME QUILTING FEET SET
767-434-005
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E18

View proof JSONReport this claim
CONVERTIBLE FREE MOTION QUILTING FOOT SET
767-433-004
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E19

View proof JSONReport this claim
DITCH QUILTING FOOT
767-824-109
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E20

View proof JSONReport this claim
ULTRA GLIDE FOOT
767-404-028
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E21

View proof JSONReport this claim
1/4 INCH RULER FOOT SET
767-441-005
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E22

View proof JSONReport this claim
QUILT BINDER SET
846-421-007
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E23

View proof JSONReport this claim
TAPE BINDER AND BINDER FOOT WITH GUIDE
202-327-008
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E24

View proof JSONReport this claim
SPECIALIZED STRAIGHT STITCH FEET
767-406-019
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E25

View proof JSONReport this claim
CORDING FOOT (B)
202-035-006
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E26

View proof JSONReport this claim
SPECIALIZED STRAIGHT STITCH FEET
767-405-007
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E27

View proof JSONReport this claim
CORDING FOOT (A)
202-034-005
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E29

View proof JSONReport this claim
ADJUSTABLE ZIPPER FOOT
767-408-011
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E30

View proof JSONReport this claim
VELVET FOOT
767-407-102
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E31

View proof JSONReport this claim
TAPE BINDER AND BINDER FOOT WITH GUIDE
202-328-009
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E32

View proof JSONReport this claim
BEADING FOOT
202-041-108
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E33

View proof JSONReport this claim
HEMMER FOOT
761-172-004
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to presser foot only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E36

View proof JSONReport this claim

attachment · 5

ADJUSTABLE SEAM GUIDE
767-411-017
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to accessory only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E11

View proof JSONReport this claim
ADJUSTABLE SEAM GUIDE
795-806-102
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to accessory only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E15

View proof JSONReport this claim
ELASTIC GATHERING ATTACHMENT
202-523-006
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to accessory only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E28

View proof JSONReport this claim
ELASTIC GATHERING ATTACHMENT
202-037-008
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to accessory only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E34

View proof JSONReport this claim
GATHERING ATTACHMENT
202-036-100
compatible two-hop OEM matrix
Why this fits

Two cited hops: this machine is in Janome Accessory Compatibility Category · Janome Category A, and the OEM matrix lists this part for that group. Region global_en. Applies to accessory only.

Inspect complete evidence path · 2 unique proof passages: Step 1 E5, Step 2 E35

View proof JSONReport this claim

OEM compatibility programs

Documented group memberships

Group codes are namespaced to the issuing OEM program and apply only to the cited domains. They are not machine series and do not prove compatibility outside those domains.

Janome Category A

Janome Accessory Compatibility Category · code A

Applies to: accessory, presser foot

View machine-to-group evidence · 1 unique proof passage: Proof E5

View proof JSONReport this claim

Official source library

Documents used on this page

Open the exact OEM PDF page or captured HTML edition when a safe destination exists; otherwise SewGraph labels the OEM support-page fallback honestly.

Janome Global Sewing Machine Accessories Catalog

accessory compatibility

Open official source destination · 1 unique proof passage: Proof E3

Janome Global Accessories Catalog

accessory catalog

Open official source destination · 1 unique proof passage: Proof E1

Evidence library

36 exact proof passages from 2 OEM documents

Every passage below says exactly what visible fact it proves. Repeated references to the same locator are counted once; identity evidence never counts as compatibility evidence.

Open exact proof passages · 36 unique proof passages
Official OEM PDF

What this passage proves

  • Identity — preferred display name: MC9500
  • Identity — model code: MC9500
Embroidery & Sewing MC5700 SKYLINE S3 MC11000 MC10000/10001 MC9700 MC9500
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
6
Open source
Open cited PDF at page 6Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
92bd03a891a3fec57789f575362e75d92228a3dd8e141290d26f1112099b685a
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Identity — printed machine name: MC9500
Embroidery & Sewing MC5700 SKYLINE S3 MC11000 MC10000/10001 MC9700 MC9500
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
6
Open source
Open cited PDF at page 6Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
e0bb4f76041342427493ab7e855747888e2e46bd3053ea63fcc5addc54de5efe
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Identity — printed machine name: MC9500
MC9500
Document
Janome Global Sewing Machine Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
6
Open source
Open cited PDF at page 6Open OEM source or support page
Advanced technical receipt
Asset SHA-256
9580c0b4e4a53a2f13d71036bac9e214c316107ec4b06bf6fabe21982b17687e
Locator
b2cb77217d562282c1bd00459d1a0029bf9cf0e5976088827d30764a200c2cc1
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • presser foot fact — presser foot shank height: High
MC9500
Document
Janome Global Sewing Machine Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
6
Open source
Open cited PDF at page 6Open OEM source or support page
Advanced technical receipt
Asset SHA-256
9580c0b4e4a53a2f13d71036bac9e214c316107ec4b06bf6fabe21982b17687e
Locator
70910bf9f6a74380d3fdc1b46024d22d4dba8e133eec0c28c3016932d2a8287c
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • OEM program membership — Janome Accessory Compatibility Category: Janome Category A
  • Item fitment path — this machine's OEM group membership for FRINGING FOOT
  • Item fitment path — this machine's OEM group membership for TAPING FOOT
  • Item fitment path — this machine's OEM group membership for TAPING FOOT WITH REEL
  • Item fitment path — this machine's OEM group membership for BOBBIN HOLDER FOR FREE QUILTING AND HAND-LOOK STITCHING
  • Item fitment path — this machine's OEM group membership for CONCEAL ‰ ZIPPER FOOT
  • Item fitment path — this machine's OEM group membership for ADJUSTABLE SEAM GUIDE
  • Item fitment path — this machine's OEM group membership for BLIND STITCH FOOT
  • Item fitment path — this machine's OEM group membership for EVEN FEED FOOT
  • Item fitment path — this machine's OEM group membership for 1/4 INCH SEAM FOOT
  • Item fitment path — this machine's OEM group membership for BINDER FOOT WITH GUIDE
  • Item fitment path — this machine's OEM group membership for FREE MOTION COUCHING FOOT SET
  • Item fitment path — this machine's OEM group membership for FREE MOTION FRAME QUILTING FEET SET
  • Item fitment path — this machine's OEM group membership for CONVERTIBLE FREE MOTION QUILTING FOOT SET
  • Item fitment path — this machine's OEM group membership for DITCH QUILTING FOOT
  • Item fitment path — this machine's OEM group membership for ULTRA GLIDE FOOT
  • Item fitment path — this machine's OEM group membership for 1/4 INCH RULER FOOT SET
  • Item fitment path — this machine's OEM group membership for QUILT BINDER SET
  • Item fitment path — this machine's OEM group membership for TAPE BINDER AND BINDER FOOT WITH GUIDE
  • Item fitment path — this machine's OEM group membership for SPECIALIZED STRAIGHT STITCH FEET
  • Item fitment path — this machine's OEM group membership for CORDING FOOT (B)
  • Item fitment path — this machine's OEM group membership for ELASTIC GATHERING ATTACHMENT
  • Item fitment path — this machine's OEM group membership for CORDING FOOT (A)
  • Item fitment path — this machine's OEM group membership for ADJUSTABLE ZIPPER FOOT
  • Item fitment path — this machine's OEM group membership for VELVET FOOT
  • Item fitment path — this machine's OEM group membership for BEADING FOOT
  • Item fitment path — this machine's OEM group membership for GATHERING ATTACHMENT
  • Item fitment path — this machine's OEM group membership for HEMMER FOOT
Embroidery & Sewing MC5700 SKYLINE S3 MC11000 MC10000/10001 MC9700 MC9500
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
6
Open source
Open cited PDF at page 6Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
10f7ba80a8e3d8f7eedae2effc7d00f04921fdfb9479b917e3ea70c3f9bb11a2
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: FRINGING FOOT (compatible)
200-016-108 A
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
35
Open source
Open cited PDF at page 35Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
4f46e0769ba6aebaf655eb91c74763978ed92217247aad1c6da7cebe352affcd
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: TAPING FOOT (compatible)
767-412-018 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
54
Open source
Open cited PDF at page 54Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
26e57f6b30f5123d07fc942e6b6a5a3a758e87e6717312f4644108881c0ac933
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: TAPING FOOT WITH REEL (compatible)
202-033-004 A B C D E F G H
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
39
Open source
Open cited PDF at page 39Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
7c3f16a807e2b176bff12134fdafebf5fb4dc30be3b163cbc2993dcf50bc7579
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: BOBBIN HOLDER FOR FREE QUILTING AND HAND-LOOK STITCHING (compatible)
200-445-007 A C
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
34
Open source
Open cited PDF at page 34Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
992c89a4d45a19d043b281dfedc69f57b120c328ff67bd3c6fbb487d3fd701b2
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: CONCEAL ‰ ZIPPER FOOT (compatible)
767-410-016 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
55
Open source
Open cited PDF at page 55Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
590d4df1d331e70b89894b5db143c9e949e1eab999f6dad649ce3e382611a587
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — attachment: ADJUSTABLE SEAM GUIDE (compatible)
767-411-017 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
55
Open source
Open cited PDF at page 55Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
b7d4b5f736ce710ba83f3de3c1c2e2ac8fe3fa19775f54a9189a78c08c92ed83
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: BLIND STITCH FOOT (compatible)
202-040-004 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
39
Open source
Open cited PDF at page 39Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
82d2c53c873ac3ec130d05010f0eaa30829104a94af6499872bd6fc8c4d7512d
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: EVEN FEED FOOT (compatible)
767-403-016 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
53
Open source
Open cited PDF at page 53Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
6d8153b24069c652656c7d3f93dfcb9f3111caf79ecd2d93340d85e935b9053e
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: 1/4 INCH SEAM FOOT (compatible)
767-820-105 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
52
Open source
Open cited PDF at page 52Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
cf90b3c4e19c9666a995c9e6700b78ffc0af67c9cbfc715d68076aef2bd9a2f6
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — attachment: ADJUSTABLE SEAM GUIDE (compatible)
795-806-102 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
43
Open source
Open cited PDF at page 43Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
91666857b33d6fc4d352b994079bb6d15efdccfc5d843a4f823ea031d03ba83f
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: BINDER FOOT WITH GUIDE (compatible)
796-402-004 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
45
Open source
Open cited PDF at page 45Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
0078ad4090869b7f0928ed6e0a85a64bb7d203862ea0ef34c15be834b2fef72e
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: FREE MOTION COUCHING FOOT SET (compatible)
202-110-006 A C
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
34
Open source
Open cited PDF at page 34Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
9e36f972a58c657669a7dc1e826a2748fde935f5b80308123a9d78c7c988935a
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: FREE MOTION FRAME QUILTING FEET SET (compatible)
767-434-005 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
57
Open source
Open cited PDF at page 57Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
d1e117d2ab727689e680bdbf170aa52f5e7d3496222998078b2f71b6ac75e054
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: CONVERTIBLE FREE MOTION QUILTING FOOT SET (compatible)
767-433-004 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
56
Open source
Open cited PDF at page 56Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
9a6e70da52adeef3b62d4c348741ac58544e9eaa2009728f759f3a244a8e348e
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: DITCH QUILTING FOOT (compatible)
767-824-109 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
52
Open source
Open cited PDF at page 52Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
b8e88e7b0bafcf6d7885bfd7fddad24e86c83365f86a034da857a0fc02c21966
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: ULTRA GLIDE FOOT (compatible)
767-404-028 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
50
Open source
Open cited PDF at page 50Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
4bd47a2ddeca9e85c3dd4ee2688f41808f02d651d0bd5aa0679f2dee485187d8
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: 1/4 INCH RULER FOOT SET (compatible)
767-441-005 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
57
Open source
Open cited PDF at page 57Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
59f61a168e0a67e9cec1dce85597c9404e26eba6f47039cc310c00a4684c6de1
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: QUILT BINDER SET (compatible)
846-421-007 A C
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
37
Open source
Open cited PDF at page 37Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
1a8116ccadc4fbf41b0284a1c410e7933504599272aeb93b581606edfe7a2c32
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: TAPE BINDER AND BINDER FOOT WITH GUIDE (compatible)
202-327-008 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
45
Open source
Open cited PDF at page 45Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
9ea35fed5f2d8fea384f7cae734eb44a06701e4867ea779d76baf7497ba0378f
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: SPECIALIZED STRAIGHT STITCH FEET (compatible)
767-406-019 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
51
Open source
Open cited PDF at page 51Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
b80b972e015a67cf60f8fe36adcfb7c5b45090fbc8cc667c972a748d93220660
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: CORDING FOOT (B) (compatible)
202-035-006 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
38
Open source
Open cited PDF at page 38Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
ba582fe7b33ca5a917345d06d3d6ec1ccddf8b6ce59ed6487570c24e9c4a3701
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: SPECIALIZED STRAIGHT STITCH FEET (compatible)
767-405-007 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
51
Open source
Open cited PDF at page 51Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
0862df60403c064b21d755f36b1182a74a22167d82defea3793e1695e96adb68
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — attachment: ELASTIC GATHERING ATTACHMENT (compatible)
202-523-006 A B C D E F G H
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
39
Open source
Open cited PDF at page 39Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
91f5f34a8b0e323f3f184e99eaeaab37b3e5528c42b717fa03fdf40ada2efabe
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: CORDING FOOT (A) (compatible)
202-034-005 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
40
Open source
Open cited PDF at page 40Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
6cc0bec8dda151ce59523caa0c5f48741dfc9a48943d672d06859e206bd9f2fd
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: ADJUSTABLE ZIPPER FOOT (compatible)
767-408-011 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
54
Open source
Open cited PDF at page 54Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
fce667ca5fc8f215f27230d2144b9a37a4ba911aaa8ddf103aa4f7110c70f17e
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: VELVET FOOT (compatible)
767-407-102 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
51
Open source
Open cited PDF at page 51Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
3d2fcf1dd0d79de56e263eadbebe41948ce11728e0b58ff8244047ebf601538f
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: TAPE BINDER AND BINDER FOOT WITH GUIDE (compatible)
202-328-009 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
45
Open source
Open cited PDF at page 45Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
cce60255e48c24add0d557a419f591e59743293066a6b3cf2713b213505e881d
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: BEADING FOOT (compatible)
202-041-108 A B C D E F G H
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
40
Open source
Open cited PDF at page 40Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
ba1be4d6020bc961fc90ac72a8d81142d9835575b2e59c6468c28c0ad45fca5f
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — attachment: ELASTIC GATHERING ATTACHMENT (compatible)
202-037-008 A B C D E F G H
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
39
Open source
Open cited PDF at page 39Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
2c83f1dec3745d5ff2cc4f9c10b69cdc2b7b58444b46515992bf3b8ed9b7e897
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — attachment: GATHERING ATTACHMENT (compatible)
202-036-100 A B C D E F G H *I J K
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
41
Open source
Open cited PDF at page 41Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
c7716fe484bdf192e92f8bc137f44cbb6a19ade56f118bce33cd54eb4cfa78b5
Destination status
direct_pdf
Official OEM PDF

What this passage proves

  • Item fitment — presser foot: HEMMER FOOT (compatible)
761-172-004 A B C D E F G H I J K L
Document
Janome Global Accessories Catalog
Issuer
Janome
Extraction
native
PDF page
52
Open source
Open cited PDF at page 52Open OEM source or support page
Advanced technical receipt
Asset SHA-256
896123f19932823c009a23ae608dbdddf35b675f54937023871be4fe210837b1
Locator
2485b57f6f39e1e91cd1c9098d6ed8e4b66596afb299f72d222f3da81d12a0aa
Destination status
direct_pdf

What is supported, and what remains open?

0 supported answers and 8 answers with conditions or remaining limits. Evidence coverage is not a probability of accuracy.

Unresolved owner questions (3)
  • Class system: Not established — Not yet verified: The procedure does not establish bobbin class, dimensions, material, part number, case identity, or substitution.
  • System type: Not established — Not yet verified: The exact pages do not establish a standardized needle-system designation or cross-brand substitution.
  • Mount or fit: Not established — Not yet verified: The packet does not establish a standardized mount, shank, adapter, or compatible-item fit.

Report a correction or share an OEM source

Advanced provenance and dataset receipt

Public snapshot a1cc1aceef228fcf33329e37165ab888ce5b9fe3f13eb56967ae0fbf41d8d8a7

Catalog e156281c7d3048027b5ac89e7476be8f54dd5a9309505e96260b0455d3cd2a7e · exact native quotes only · dossier method sewgraph-model-dossier-v2