Check the conditions alongside each answer. Foot attachment, shank type and adapter requirements are separate; one does not establish universal accessory fit.
Bobbins and hook
How does the bobbin case load?
conditional
The machine uses a removable bobbin case that is inserted fully into the hook and secured by closing the case latch before the slide plate is closed.
Turn the power off before opening the slide plate and bring the needle up before removing the case.
With the case latch open, place the bobbin so it runs clockwise, pass thread through the case slit and under the tension spring, leave about 10 cm, then insert the case fully into the hook, close its latch and close the slide plate.
Turn power off before opening the slide plate; bring the needle up before removing the case.
Turn power off, lower the presser foot, raise the needle bar to its highest position, insert the needle fully with its flat face to the right, then tighten the clamp screw.
Follow the stated order and use a straight needle.
Turn power off and remove the current foot. Fit the upper-feed foot lever's fork to the needle clamp, insert its mounting portion into the presser bar and tighten its screw securely. Turn the handwheel by hand in the sewing direction to confirm the fork position before turning power on.
Confirm the fork position by hand before power-on; the manual presents this procedure only for its upper-feed presser foot.
How is the quilting foot installed and configured?
conditional
With power off, place the quilting-foot plate on the needle-clamp screw, insert the mounting portion into the presser bar and tighten its screw. Lower the feed dogs, set stitch length to 0, adjust pressure until the green bar is at the top of its window, then lower the foot and sew.
Keep power off during replacement and preserve the stated setup order before sewing.
How does the bobbin case load?: The machine uses a removable bobbin case that is inserted fully into the hook and secured by closing the case latch before the slide plate is closed.
How is the bobbin inserted and threaded?: With the case latch open, place the bobbin so it runs clockwise, pass thread through the case slit and under the tension spring, leave about 10 cm, then insert the case fully into the hook, close its latch and close the slide plate.
Insert the bobbin case fully into the hook
close the bobbin case latch
Close the slide plate.
Which needle system applies?: Use needle system HLx5 or HAx1.
Which way does the needle face?: Turn power off, lower the presser foot, raise the needle bar to its highest position, insert the needle fully with its flat face to the right, then tighten the clamp screw.
Which needle matches each topstitch-thread count?: For the manual's topstitch-thread table, use No.11 with thread #80-50, No.14(11) with #60-50, No.16 with #50-30, and No.18 with #20-8.
Turn off power.
flat face of the new needle facing to the right
until it can go no further
The needle to be used is HLx5 or HAx1.
#20-8
No.18
How is the bobbin inserted and threaded?: With the case latch open, place the bobbin so it runs clockwise, pass thread through the case slit and under the tension spring, leave about 10 cm, then insert the case fully into the hook, close its latch and close the slide plate.
Loading the bobbin into the bobbin case.
bobbin runs clockwise
under the thread tension spring
about 10cm
How does the bobbin case load?: The machine uses a removable bobbin case that is inserted fully into the hook and secured by closing the case latch before the slide plate is closed.
How is the bobbin inserted and threaded?: With the case latch open, place the bobbin so it runs clockwise, pass thread through the case slit and under the tension spring, leave about 10 cm, then insert the case fully into the hook, close its latch and close the slide plate.
Take out the bobbin case.
Bring up the needle.
Turn OFF the power switch when opening the slide plate.
How is the upper-feed foot installed safely?: Turn power off and remove the current foot. Fit the upper-feed foot lever's fork to the needle clamp, insert its mounting portion into the presser bar and tighten its screw securely. Turn the handwheel by hand in the sewing direction to confirm the fork position before turning power on.
Which pressure and speed settings apply to the upper-feed foot?: Use low presser-foot pressure with the upper-feed foot, the lowest pressure for velvet, and operate at medium speed.
Turn off power and
Fit forked portion of the actuating lever to the needle clamp
insert the installing portion into the presser bar
rotate handwheel by hand in sewing direction
Use the sewing machine at medium speed.
How is the quilting foot installed and configured?: With power off, place the quilting-foot plate on the needle-clamp screw, insert the mounting portion into the presser bar and tighten its screw. Lower the feed dogs, set stitch length to 0, adjust pressure until the green bar is at the top of its window, then lower the foot and sew.
Turn off power. Install the quilting foot.
Put the plate on the needle clamp screw
Position Feed Dog in lower position.
Position stitch length adjusting dial
Lower the foot and start sewing.
Unknown is not incompatible. A missing answer means the current official evidence does not support one yet.
Specifications
Documented machine facts
Multiple cited representations for one field share one row. SewGraph preserves every value and exact proof passage; it does not guess which representation is “raw” or “normalized” when the public projection does not label that distinction.
Open the exact OEM PDF page or captured HTML edition when a safe destination exists; otherwise SewGraph labels the OEM support-page fallback honestly.
juki_tl2010q_2000qi_parts_list_40099541
parts
Open official source destination · 1 unique proof passage:Proof E1
JUKI TL-2010Q instruction manual
instruction
Open official source destination · 1 unique proof passage:Proof E2
Evidence library
7 exact proof passages from 2 OEM documents
Every passage below says exactly what visible fact it proves. Repeated references to the same locator are counted once; identity evidence never counts as compatibility evidence.
Open exact proof passages · 7 unique proof passages
Official OEM PDF
What this passage proves
Identity — printed machine name: TL-2010Q
TL-2010Q/2000Qi
Document
juki_tl2010q_2000qi_parts_list_40099541
Issuer
JUKI
Extraction
native
PDF page
1
Open source
Public source link unavailable; the cited bytes remain identified below.
TL-2010Q
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
IMPORTANT:
Read all safety regulations carefully and under-
stand them before using your sewing
Install the upper feed presser foot.
Fit forked portion of the actuating lever to the needle clamp, insert the installing
portion into the presser bar, and securely tighten the screw in the presser foot.
0 supported answers and 8 answers with conditions or remaining limits. Evidence coverage is not a probability of accuracy.
Unresolved owner questions (3)
Which standardized bobbin class applies?: Not established — Not yet verified: The reviewed instruction-manual pages do not state a standardized bobbin class.
What are the bobbin dimensions and material?: Not established — Not yet verified: The reviewed instruction-manual pages do not establish bobbin dimensions or material.
Do generic or third-party feet universally fit?: Not established — Not yet verified: The reviewed manual does not establish universal shank, adapter, snap-on or third-party-foot compatibility.