Check the conditions alongside each answer. Foot attachment, shank type and adapter requirements are separate; one does not establish universal accessory fit.
Presser feet and adapters
How do ordinary presser feet attach?
conditional
Native snap-on feet. Ordinary feet snap onto the presser-foot holder.
Raise the needle before changing the foot. Align the foot pin with the holder and lower the lifter. This establishes foot-to-holder attachment only.
Which Singer needle types and sizes does the manual list?
conditional
Singer 2020 needles: 11/80, 14/90, 16/100 and 18/110 for woven fabrics; Singer 2045: 11/80, 14/90 and 16/100 for knits.
Choose the type and size using the manual's fabric-weight and thread table. These are source-native Singer needle codes, not a normalized universal system claim.
Which Singer needle types and sizes does the manual list?: Singer 2020 needles: 11/80, 14/90, 16/100 and 18/110 for woven fabrics; Singer 2045: 11/80, 14/90 and 16/100 for knits.
NEEDLE, THREAD AND FABRIC CHART
2020
2045
11/80
18/110
How is the bobbin case installed?: Install the case with its locating pin straight up and the thread toward you.
Hold the latch open, with locating pin straight up.
Slide the bobbin case onto the center spindle of the shuttle, with the thread toward you.
Be sure the locating pin fits into the locating groove at the top of the shuttle.
How is the shuttle area cleaned?: Remove the bobbin case, move the two shuttle keepers aside, and remove the race cover and shuttle before brushing the feed dogs and shuttle area.
Where does the owner manual specify oil?: Apply one drop of sewing-machine oil to the shuttle center pin and shuttle race where indicated.
Remove the bobbin case from the shuttle.
Push aside the two shuttle keepers.
Remove the shuttle race cover and shuttle.
Clean the feed dogs and shuttle area with the lint brush.
Put a drop of sewing machine oil on the center pin of the shuttle and shuttle race
Which way does the needle face?: Insert the needle with its flat side toward the back and push it fully upward.
Always disconnect the machine from power supply
Insert the new needle into the needle clamp with the flat side toward the back.
Push the needle up as far as it can go.
Which stitch settings can be adjusted?: Stitch length, stitch width and straight-stitch needle position can be adjusted with the control-panel buttons.
You can manually change the length, width or needle position for straight stitch
Some patterns offer more options for manual adjustments than others.
Which way should bobbin thread unwind?: Place the bobbin in its case with the thread running clockwise.
Hold the bobbin in your right hand with the thread running clockwise.
Pull the thread through the slit in the case and then underneath the flat tension spring.
Domains with cited compatible items: presser foot (9)
bobbin
Core answer answered
needle
Reviewed — not established
presser foot
9 cited items; core not established
Unknown is not incompatible. A missing answer means the current official evidence does not support one yet.
Specifications
Documented machine facts
Multiple cited representations for one field share one row. SewGraph preserves every value and exact proof passage; it does not guess which representation is “raw” or “normalized” when the public projection does not label that distinction.
A two-hop result joins the machine’s official accessory-group membership to the OEM part matrix. Open the evidence to inspect both hops.
9 relationships shown
presser foot · 9
CORDING FOOT 250006345
compatibletwo-hop OEM matrix
Why this fits
Two cited hops: this machine is in SINGER Accessory M/C Code · SINGER M/C Code CA, and the OEM matrix lists this part for that group. Edition 2022. Region global_en. Applies to presser foot only.
Two cited hops: this machine is in SINGER Accessory M/C Code · SINGER M/C Code CA, and the OEM matrix lists this part for that group. Edition 2022. Region global_en. Applies to presser foot only.
Two cited hops: this machine is in SINGER Accessory M/C Code · SINGER M/C Code CA, and the OEM matrix lists this part for that group. Edition 2022. Region global_en. Applies to presser foot only.
Two cited hops: this machine is in SINGER Accessory M/C Code · SINGER M/C Code CA, and the OEM matrix lists this part for that group. Edition 2022. Region global_en. Applies to presser foot only.
Two cited hops: this machine is in SINGER Accessory M/C Code · SINGER M/C Code CA, and the OEM matrix lists this part for that group. Edition 2022. Region global_en. Applies to presser foot only.
Two cited hops: this machine is in SINGER Accessory M/C Code · SINGER M/C Code CA, and the OEM matrix lists this part for that group. Edition 2022. Region global_en. Applies to presser foot only.
Two cited hops: this machine is in SINGER Accessory M/C Code · SINGER M/C Code CA, and the OEM matrix lists this part for that group. Edition 2022. Region global_en. Applies to presser foot only.
Two cited hops: this machine is in SINGER Accessory M/C Code · SINGER M/C Code CA, and the OEM matrix lists this part for that group. Edition 2022. Region global_en. Applies to presser foot only.
Two cited hops: this machine is in SINGER Accessory M/C Code · SINGER M/C Code CA, and the OEM matrix lists this part for that group. Edition 2022. Region global_en. Applies to presser foot only.
Group codes are namespaced to the issuing OEM program and apply only to the cited domains. They are not machine series and do not prove compatibility outside those domains.
Open official source destination · 1 unique proof passage:Proof E4
Evidence library
18 exact proof passages from 4 OEM documents
Every passage below says exactly what visible fact it proves. Repeated references to the same locator are counted once; identity evidence never counts as compatibility evidence.
Open exact proof passages · 18 unique proof passages
2 supported answers and 10 answers with conditions or remaining limits. Evidence coverage is not a probability of accuracy.
Unresolved owner questions (9)
What shank type is it?: Not established — Not yet verified: No low-, high- or other shank class is established by the reviewed passages.
Can the presser-foot holder be removed?: Not established — Not yet verified: The reviewed passages do not establish how the holder attaches to or is removed from the presser bar.
Will generic screw-on feet fit?: Not established — Not yet verified: Universal screw-on-foot acceptance is not established by snap-on foot-to-holder instructions.
Which third-party adapters fit?: Not established — Not yet verified: No third-party adapter compatibility is established.
Which bobbin dimensions and materials are interchangeable?: Not established — Not yet verified: Dimensions, material and substitution equivalence beyond the OEM Class 15 instruction are not established.
What hook system does it use?: Not established — Not yet verified: The manual names a shuttle but does not establish the site's standardized hook/drive classification.
What is its normalized needle system?: Not established — Not yet verified: A normalized cross-brand needle-system designation is not established by these passages.
What is its maximum stitch width?: Not established — Not yet verified: No machine-wide maximum stitch width is assigned without an exact model-to-column bridge.
How many built-in stitches does model 6180 have?: Not established — Not yet verified: The shared manual's 60-, 80- and 100-stitch qualifiers are not mapped to model 6180.